Relay protection tester

2022-06-27   


1. It integrates optical digital test and small signal analog test functions, and can be connected to external current and voltage power amplifier.
2. Support 10 channels of SMV message output independently complying with IEC60044-8 (FT3) specification and 1 channel of input; Support synchronous / asynchronous transmission mode and multiple transmission rates.
3. It supports the output of 8 groups of sampled value (SMV) messages conforming to iec61850-9-2 specification, and the output of sampling points at equal intervals, fully meeting the latest standards of the State Grid.
4. It supports 12 groups of goose output and 8 groups of goose input, which can be configured on any optical port.
5. It can automatically detect optical digital signals and realize the automatic configuration of SMV and goose information.
6. With virtual terminal test function.
7. It has the function of message oscillograph, can receive and analyze the sampling value (SMV) message and goose message conforming to iec61850-9-2 specification, and realize the self loop test of device output; At the same time, it can receive the optical digital signal sent by the merging unit (MU) or other ied equipment, and display its waveform, amplitude, angle and frequency in real time.
8. It has powerful functions of message recording, message online alarm and offline message analysis.
9. Multiple groups of goose messages can be received or sent.

10. The transceiver optical ports of SMV and goose can be configured arbitrarily, either as the same optical port or as an independent transceiver.
11. Completely analyze the protection model files (ICD, CID, SCD, etc.), realize the automatic configuration of current and voltage channel selection, proportional coefficient, asdu number, sampling rate, goose information, etc., and simply and conveniently realize the protection test to improve work efficiency.
12. It can perform message test functions such as frame loss, out of step, flying point, wrong sequence, invalid quality bit setting, wrong value test, etc.
13. It has GPS, IRIG-B and IEEE1588 synchronous time synchronization functions.
14. It has the commissioning function of standby automatic switching device.
15. 12 channels of independent analog small signal output, which can be compatible with testing all kinds of protection receiving electronic transformer signals; Or connect power sources of various brands to carry out comparison test between ordinary protection and digital protection.
16. 8 pairs of input quantity, 4 pairs of general output quantity, 4 pairs of fast output quantity, goose information message, realizing complete closed-loop test of protection.
17. The software has rich testing functions, and can test various microcomputer protection devices such as line protection, bus protection, transformer protection, generator transformer unit protection and standby automatic switching devices.
18. Support standard COMTRADE format waveform playback.

Mf3000 optical digital relay protection tester (non industrial control mf3000a and industrial control mf3000b) developed by Chengdu Tianjin Instrument Co., Ltd. is applicable to all digital substations complying with IEC 61850 specification. It can not only output sampling value messages based on IEC 61850-9-2le and iec60044-7/8, but also receive and send goose messages.
Open protocol, SMV and goose messages support flexible configuration to realize seamless connection with products of any manufacturer. In addition to the digital output based on IEC 61850, the tester can also output 0~7v small signal analog quantity. At the same time, the tester supports hard input and output to meet the testing needs of low-voltage protection devices in digital substations.
Various combinations of digital output, analog output, hard input / output and goose can be realized through simple configuration. The tester can provide test solutions for relay protection devices with various input / output modes. Even when the output voltage is 40mv, it can still maintain extremely high accuracy, and the overall output accuracy meets the requirements of class 0.05. Simulate the abnormal process layer equipment, flexibly set the channel quality factor, sampling frame loss point, etc., and provide a detailed solution for assessing the correct response of bay layer ied in case of abnormal process layer equipment.

 


Contact Person:Zhourong Wang

Email:wang_zr@tesient.cn

》》》Online Store——Buy Now》》》

Disclaimer: This article is reproduced from other media. The purpose of reprinting is to convey more information. It does not mean that this website agrees with its views and is responsible for its authenticity, and does not bear any legal responsibility. All resources on this site are collected on the Internet. The purpose of sharing is for everyone's learning and reference only. If there is copyright or intellectual property infringement, please leave us a message.

Newest

Links

Back to top
©Copyright 2009-2020 American news network      Contact Us   SiteMap